Recommended High and Low Level Subwoofer Connection for Primare Amplifiers

1. Introduction: Choosing the Correct Subwoofer Connection

Several leading subwoofer manufacturers recommend high-level (speaker-level) connections to achieve optimal integration between subwoofers and the main loudspeakers.

A high-level connection takes its signal directly from the amplifier’s speaker outputs. This means the subwoofer receives the same source signal as the main loudspeakers, including the amplifier’s volume adjustments and signal characteristics. This can help achieve consistent tonal balance and a natural transition between the main loudspeakers and subwoofer.

A high-level subwoofer connection does not automatically guarantee identical timing or phase behaviour between the main loudspeakers and subwoofer. It provides a shared amplifier signal reference, but actual integration also depends on crossover characteristics, filtering, phase, group delay, room acoustics and placement.

However, not all amplifier output designs support conventional high-level subwoofer connections. Certain Primare amplifiers use output topologies that make some standard connection methods unsuitable, particularly when connecting a single subwoofer in stereo.

The recommended connection method therefore depends on the Primare amplifier model, its output topology, and the number of subwoofers being used.

This guide describes the recommended connection methods for different Primare amplifier models and configurations.

2. Understanding High-Level Subwoofer Connections

A conventional stereo high-level connection uses three conductors:

  • Red: Connect to the positive (+) speaker output of one amplifier channel.
  • Yellow: Connect to the positive (+) speaker output of the other amplifier channel.
  • Black: Connect to the appropriate signal ground, as specified below.

This arrangement allows a single subwoofer to receive a stereo-derived signal through its high-level input.

Important: Ground Connection

Our general recommendation is to connect the black subwoofer lead to the ground collar of an RCA connector or the ground pin of an XLR connector, then connect it to an unused input on the amplifier or preamplifier.

Where appropriate, the black lead may alternatively be connected to the amplifier chassis ground.

Do not automatically connect the black lead to a negative (–) speaker terminal. Depending on the amplifier’s output topology, the negative speaker terminal may be an active output rather than ground. Connecting it incorrectly can result in improper operation or potentially damage the equipment.

Always follow the model-specific connection instructions in this guide.

3.1 Alternative Connection: Low-Level Stereo

When an amplifier’s output topology does not support the conventional high-level connection, the recommended alternative is a low-level stereo connection.

Connect the subwoofer to the stereo preamplifier outputs or variable analogue outputs of the integrated amplifier or preamplifier, as applicable.

This connection method can provide excellent performance and seamless integration with the main loudspeakers.

Important settings for the following models:

  • Primare I15 Prisma MK2
  • Primare SC15 Prisma MK2

For these models, set the ANALOG output to PRE to obtain a variable-level preamplifier output.

Main Loudspeaker and Subwoofer Settings

With this connection arrangement, the main loudspeakers operate full-range, while the subwoofer reproduces additional low-frequency content below its selected low-pass filter frequency.

Set the subwoofer’s low-pass filter to complement the natural low-frequency response of the main loudspeakers.

This approach allows the subwoofer to concentrate on the lowest frequencies, extending bass response while potentially improving overall tonal balance, bass definition, and soundstage presentation.

Recommended Low-Pass Filter Setting

As an initial guideline, set the subwoofer’s low-pass filter to approximately 70% of the lowest frequency specified for the main loudspeakers.

For example:

  • Main loudspeaker frequency response: 43 Hz
  • 70% of 43 Hz: approximately 30 Hz
  • Suggested initial subwoofer low-pass setting: 30 Hz

This is a starting point rather than a universal rule. The optimum setting depends on the loudspeaker’s actual in-room response, its natural low-frequency roll-off, room acoustics, and the subwoofer’s characteristics.

Make final adjustments by listening and, where possible, measuring the combined system response.

Subwoofers with a Single Low-Level Input

Some subwoofers have only one low-level input rather than separate left and right inputs.

If using two subwoofers is not practical, a Y-adapter can combine the left and right preamplifier outputs into a single subwoofer input.

However, depending on the equipment’s input and output circuitry, this arrangement may introduce unwanted interaction between the two output channels.

We recommend testing the arrangement with an inexpensive Y-adapter and cable before committing to a permanent installation.

If this does not work satisfactorily, some customers have reported excellent results using a single-channel connection:

  • Connect to either the left or right variable-level output.
  • Alternatively, where supported, use the left speaker output for a high-level connection.

The appropriate method depends on the amplifier and subwoofer configuration.

3.2 Alternative Connection: Subwoofer Outputs

If your integrated amplifier or preamplifier provides dedicated subwoofer outputs with bass-management controls, we recommend using them to connect your subwoofer. This is generally the most convenient and effective way to integrate a subwoofer into your system. Bass management allows you to redirect low-frequency signals to the subwoofer while reducing the low-frequency demands on the main speakers. This helps prevent the main speakers from having to reproduce frequencies below their optimal operating range.

4. Recommended Connections: Primare Stereo Amplifiers

4.1 Models Supporting Conventional Stereo High-Level Connection

Applicable models:

928 / 202 / 301 / A10 / A20 / A30.1 / A30.2 / A31.2 / I30 / I21 / A32 / A60

One Subwoofer: Stereo Configuration

Connect as follows:

Subwoofer lead

Amplifier connection

Red

Positive (+) speaker output of one channel

Yellow

Positive (+) speaker output of the other channel

Black

RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input, or appropriate chassis ground


Two Subwoofers: Stereo Configuration

Use one subwoofer for each amplifier channel.

Right-channel subwoofer:

Subwoofer lead

Amplifier connection

Red and Yellow

Right-channel positive (+) speaker output

Black

RCA ground collar or XLR ground pin connected to an unused input or appropriate chassis ground

Left-channel subwoofer:

Subwoofer lead

Amplifier connection

Red and Yellow

Left-channel positive (+) speaker output

Black

RCA ground collar or XLR ground pin connected to an unused input or appropriate chassis ground


4.2 Models Requiring Low-Level Stereo Connection for One Subwoofer

Applicable models:

I15 / I25 / I35 / A35.2 / I32 / A34.2

One Subwoofer

Use a stereo low-level connection from the variable-level preamplifier outputs.

This is the recommended connection method for a single subwoofer with these amplifier models.

Two Subwoofers

A high-level connection can be used with one subwoofer assigned to each amplifier channel.

Right-channel subwoofer:

Subwoofer lead

Amplifier connection

Red and Yellow

Right-channel positive (+) speaker output

Black

RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input, or appropriate chassis ground

Left-channel subwoofer:

Subwoofer lead

Amplifier connection

Red and Yellow

Left-channel negative (–) speaker output

Black

RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input, or appropriate chassis ground

Important notes:

  1. The left-channel connection uses the negative (–) speaker output. This is a model-specific arrangement and must not be applied to other amplifier models.
  2. The subwoofer phase setting for the left channel may need to be reversed relative to the right channel.
  3. Connecting both red and yellow leads to a single speaker output may produce an excessive input signal, depending on the subwoofer’s input design.
  4. If the input signal is too high, disconnect either the red or yellow lead. Insulate the unused bare wire to prevent accidental contact.

5. Primare A34.2 and A35.2: Bridged Mono Configuration

When two A34.2 or A35.2 amplifiers are operated in bridged mono mode, the following high-level connection arrangements apply.

Important: These connections are specific to the bridged configuration. Do not assume that the negative speaker terminals are ground.

5.1 One Subwoofer: Stereo-Derived Connection

Connect the subwoofer across the two amplifiers:

Subwoofer lead

Amplifier connection

Red

Positive (+) speaker output of the first amplifier

Yellow

Positive (+) speaker output of the second amplifier

Black

RCA ground collar or XLR ground pin connected to an unused input or appropriate chassis ground


5.2 Two Subwoofers: One Per Amplifier

Connect one subwoofer to each bridged amplifier.

First amplifier:

  • Red and Yellow: Positive (+) speaker output.
  • Black: RCA ground collar or XLR ground pin connected to an unused input or appropriate chassis ground.

Second amplifier:

  • Red and Yellow: Positive (+) speaker output.
  • Black: RCA ground collar or XLR ground pin connected to an unused input or appropriate chassis ground.

6. Recommended Connections: Primare Multi-Channel Amplifiers

Primare multi-channel amplifiers may require different high-level connection arrangements depending on the output topology and polarity of individual channels.

The active and ground speaker terminals must be identified before connecting a subwoofer.

The following recommendations are model-specific.

6.1 Primare A30.3 and A30.5

One Subwoofer: Stereo Configuration

Use the conventional stereo high-level connection:

Subwoofer lead

Amplifier connection

Red

Positive (+) speaker output of one channel

Yellow

Positive (+) speaker output of the other channel

Black

RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input, or appropriate chassis ground

One Subwoofer Per Channel

For each subwoofer:

  • Red and Yellow: Positive (+) speaker output of the corresponding channel.
  • Black: RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input, or appropriate chassis ground.

6.2 Primare SPA22 and SPA23

The SPA22 and SPA23 use different speaker output polarities for the front channels and surround/centre channels.

Follow the appropriate connection instructions for each channel group.

Front Left and Right Channels

The red speaker terminal is active (+), and the black speaker terminal is ground (–).

Use the conventional stereo high-level connection:

Subwoofer lead

Amplifier connection

Red

Right-channel red (+) speaker output

Yellow

Left-channel red (+) speaker output

Black

RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input

Surround Left and Right Channels

The black speaker terminal is active (+), and the red speaker terminal is ground (–).

Connect as follows:

Subwoofer lead

Amplifier connection

Red

Right-channel black (active) speaker output

Yellow

Left-channel black (active) speaker output

Black

Right- or left-channel red (ground) speaker output, or RCA/XLR ground connected to an unused amplifier or preamplifier input

Note: The subwoofer phase setting may need to be reversed relative to the front-channel configuration.

Centre Channel

The black speaker terminal is active (+), and the red speaker terminal is ground (–).

Connect as follows:

  • Red and Yellow: Black (active) speaker output.
  • Black: RCA ground collar or XLR ground pin connected to an unused amplifier or preamplifier input.

Important: Connecting both red and yellow leads to the same speaker output may produce an excessive input signal, depending on the subwoofer’s input design.

If necessary, disconnect one lead and insulate its exposed wire.

The subwoofer phase setting may also need to be reversed relative to the front-channel configuration.

6.3 Primare A30.7 Multi-Channel Amplifier

The A30.7 has two different speaker output polarities:

  • Channels 1, 2, 3 and 4: Black speaker terminal active (+); red speaker terminal ground (–).
  • Channels 5, 6 and 7: Red speaker terminal active (+); black speaker terminal ground (–).

This distinction is important when selecting channels for high-level subwoofer connections.

Channels 1–4

For channels 1–4:

Subwoofer lead

Amplifier connection

Red

Right-channel black (active) speaker output

Yellow

Left-channel black (active) speaker output

Black

Right- or left-channel red (ground) speaker output, or RCA/XLR ground connected to an unused amplifier or preamplifier input

Channels 5–7

For channels 5–7:

Subwoofer lead

Amplifier connection

Red

Right-channel red (active) speaker output

Yellow

Left-channel red (active) speaker output

Black

Right- or left-channel black (ground) speaker output, or RCA/XLR ground connected to an unused amplifier or preamplifier input


Recommended System Configurations

Five-, Six- or Seven-Channel Home Cinema System

Amplifier channels

Speaker assignment

Recommended connection

5 and 7

Main left and right

Conventional high-level connection

6

Centre

Single-subwoofer-per-channel connection

1–4

Surround/rear channels

High-level connection using the channel 1–4 polarity arrangement

For channels 1–4, connect:

  • Red: Right-channel black (active) speaker output.
  • Yellow: Left-channel black (active) speaker output.
  • Black: Red (ground) speaker output of either channel, or appropriate RCA/XLR ground connection.


Five-Channel Bi-Amped Main Loudspeaker System

When using channels 1–4 to bi-amplify the main left and right loudspeakers, connect each pair of amplifier channels to the corresponding bass and treble inputs of the loudspeakers, following the loudspeaker manufacturer’s bi-amplification instructions.

Use the following channel assignments:

Amplifier channels

Speaker assignment

Recommended connection

1–4

Bi-amplified front left and right

High-level connection using the channel 1–4 polarity arrangement

5 and 7

Surround/rear channels

Conventional high-level connection

6

Centre

Single-subwoofer-per-channel connection

Note: The subwoofer phase setting for channels 1–4 may need to be reversed relative to channels 5–7.


6.4 Primare A35.8

The A35.8 has model-specific speaker output polarities in both stereo and bridged operating modes.

For high-level subwoofer connections, use the following terminal assignments.

General connection instructions:

  • Red and Yellow: Connect to the active (+) speaker outputs.
  • Black: Connect to the corresponding ground (–) speaker output, or to an appropriate RCA/XLR ground connection.
  • Alternatively, the black lead may be left unconnected if the subwoofer receives the signal correctly and no hum is present, provided this connection arrangement is supported by the subwoofer manufacturer.

Speaker Output Polarity

Output

Red terminal

Black terminal

SP1

–

+

SP1 Bridged

+

–

SP2

+

–

SP3

–

+

SP3 Bridged

+

–

SP4

+

–

SP5

–

+

SP5 Bridged

+

–

SP6

+

–

SP7

–

+

SP7 Bridged

+

–

SP8

+

–

Notes

  1. The phase setting for even-numbered channels (2, 4, 6 and 8) may need to be reversed relative to odd-numbered channels (1, 3, 5 and 7).
  2. Connecting both red and yellow leads to a single speaker output may produce an excessive input signal, depending on the subwoofer’s input design. If necessary, disconnect one lead and insulate the exposed wire.
  3. For stereo left/right speaker pairs, we recommend using either odd-numbered or even-numbered unbridged output pairs, as appropriate.

6.5 Primare SPA25 Prisma Home Cinema Processor/Integrated Amplifier

The SPA25 has model-specific speaker output polarities.

For high-level subwoofer connections, use the following terminal assignments.

General connection instructions:

  • Red and Yellow: Connect to the active (+) speaker outputs.
  • Black: Connect to the corresponding ground (–) speaker output, or to an appropriate RCA/XLR ground connection.
  • Alternatively, the black lead may be left unconnected if the subwoofer receives the signal correctly and no hum is present, provided this arrangement is supported by the subwoofer manufacturer.

Speaker Output Polarity

Channel group

Red terminal

Black terminal

Front left, centre and right

+

–

All other channels

–

+

Note: The subwoofer phase setting for the front left, centre and right channels may need to be reversed relative to the surround and height channels.


7. Important Installation and Safety Considerations

Before connecting a subwoofer to any Primare amplifier, observe the following precautions:

  1. Identify the amplifier model. Connection methods are not interchangeable across all Primare amplifiers.
  2. Check output polarity. Some amplifiers use active negative speaker terminals. A negative (–) terminal must not automatically be treated as ground.
  3. Use the recommended ground connection. Where specified, connect the subwoofer’s black lead to an appropriate RCA/XLR ground or chassis ground.
  4. Check the subwoofer input requirements. Some high-level inputs have different electrical characteristics and connection requirements.
  5. Check phase and polarity. Different amplifier channels may require different subwoofer phase settings.
  6. Avoid excessive input levels. Connecting two high-level leads to one speaker terminal may produce an excessive signal with some subwoofers.
  7. Make connections with equipment switched off. Disconnect power before changing speaker-level connections.
  8. Follow manufacturer instructions. Where the amplifier and subwoofer manufacturers specify different connection requirements, obtain technical confirmation before proceeding.

8. Summary: Choosing the Correct Connection Method

The recommended connection method depends on the Primare amplifier model and subwoofer configuration.

Primare amplifier

One subwoofer

Two subwoofers

928 / 202 / 301 / A10 / A20 / A30.1 / A30.2 / A31.2 / I30 / I21 / A32 / A60

Stereo high-level

Stereo high-level, one per channel

I15 / I25 / I35 / A35.2 / I32 / A34.2

Stereo low-level

Model-specific high-level, one per channel

A34.2 / A35.2 bridged mono

Stereo-derived high-level across two amplifiers

One high-level connection per amplifier

A30.3 / A30.5

Stereo high-level

High-level, one per channel

SPA22 / SPA23

Channel-dependent high-level

Channel-dependent high-level

A30.7

Channel-dependent high-level

Channel-dependent high-level

A35.8

Channel-dependent high-level

Channel-dependent high-level

SPA25 Prisma

Channel-dependent high-level

Channel-dependent high-level

Final recommendation: Always identify the exact Primare amplifier model and operating configuration before making high-level subwoofer connections. Where conventional high-level stereo connections are unsuitable, a stereo low-level connection from the variable-level preamplifier outputs is an excellent alternative.

Technical guidance | Updated November 2026

Translate

You can use Google Translate to translate the contents of the Primare website. To do that, select the language you would like to translate into in the list below.

Please bear in mind, since the Google Translate is an automatically generated translation, we do not take any responsibility for errors in the text.